Welcome Home

A wise individual once told me that you could take a blade from a Rough Rider knife and interchange it with a like patterned CASE knife.  I have seen this aspect in whitttler patterns from both brands.

Recently, I've picked up several CASE 75 pattern large Stockmans and wanted to compare a Rough Rider  (RR603) to one of the CASEs.

Of my 75's I chose the Orange Comp to contrast the Yellow Comp of the Rough Rider.

Out of the box the CASE was cosmetically very good, however I had issues with the Rough Rider.  The fit and finish didn't compare.  Perhaps it was a bad run, or perhaps I just got one that was "off", but the shield was noticably off and the bolster pins wasn't polished.  I did like the ring  bolsters that Rough Rider puts on their Yellow Comp series.

Definitely not the quality that I've come to expect from Rough Rider.

The blades on both knives were pretty sharp, out of the box, with the CASE having a more polished edge.  As you can see, they are pretty much the same.

The similarly ended here though.  When looking down at the knives it's very obvious that the blades on the Rough Rider we're noticably thinner than on the CASE.   

I don't have a fancy micrometer, but I'd say that they were fully only 2/3 the thickness of the CASE, while keeping the same approximate thickness at the tang.

I don't necessarily see this as a problem, as I've seen this in other knives, but I think that Rough Rider could have thinned out the tangs also and given us a thinner overall knife.

No fancy scales either, so by my hand scales, I can't really detect a noticable difference in the weight of either one.

Bottom line, for me is, I got my CASE for roughly $50.00; I got my Rough Rider for about $12.00.  I think that I'll be carrying the Rough Rider for a bit.

After some personalization, ie lowering the sheeps foot blade and rounding out the edges of the scales I'll see how it does in the long run.

Views: 114

Replies to This Discussion

Found this YouTube comparison for the RR and CASE.

https://youtu.be/TQFaBbZ7dXA

Definitely not the quality that I've come to expect from Rough Rider.

I can honestly say I am surprised JJ.  The photos alone tell me that this is not the RR quality we have all seen in the past.  Think I will make a stop at the RR booth at Blade and see is it is happening across the board with them

I'm liking the RR now that I've got the scales smoothed down some.  I'm betting that the shield issue comes from a new batch of shields being put into scales prepped for the old shield.

I'm definitely, more than a little bit, discouraged with the blades...they've been thinned down so much it's rediculous.  Can't say that it's an isolated knife, either, because you know I got 2.

I've reviewed every YouTube video with the 603s and from what I've seen, that's the way they are.

I've never seen a Rough Rider that failed, miserably, but from my standpoint, this pattern did.

Made my mind up that I'm not going to EDC the Rough Rider.  Went looking for a Yellow Comp CASE, because I wanted a CV.  Nowhere in town had the yellow, so I picked up an Amber CV.

Let the transformation begin...

O9

Jan Carter said:

Definitely not the quality that I've come to expect from Rough Rider.

I can honestly say I am surprised JJ.  The photos alone tell me that this is not the RR quality we have all seen in the past.  Think I will make a stop at the RR booth at Blade and see is it is happening across the board with them

I posted a comment, on the RR Facebook page, about this knife.  They didn't comment on it, however they did "Like" it.

It would have been nice if they'd take the time to address the issues.

Can't wait to see it in its new form :)

Awesome!  Thanks, JJ!

In case you haven't seen the post about my CASE, it broke.  Backspring is caput.  I've sent it to CASE, for repair.

In the meantime, Tobias had checked the specs and verified the "thinness" of the blades.

CASE Specs...

Rough Rider Specs...

As can be seen, the current production Rough Riders have roughly 2/3 thickness as the CASE.

He did refer me to another Rough Rider, in red bone, that according to the specs has slightly thicker blades than the CASE.

Of course they're out of stock at SMKW but I was able to find one on eBay, so I'll have something to use while the folks up in Bradford repair my CASE.

I'll see how the red bone measures up, when it arrives.

Looks like someone at SMKW (whoever runs the RR Facebook page) got a little testy about me questioning the thickness of the blades in their new knives...

I'm taking this to mean that all the new knives will have these thin blades?

RSS

White River Knives

Latest Activity


Featured
Charles Sample left a comment for Bill Chamberli
7 hours ago
J.J. Smith III posted a status
"Don't blindly follow some "EXPERT" that tells you something can't be done."
10 hours ago
J.J. Smith III left a comment for Bill Chamberli
10 hours ago
Billy Oneale left a comment for Bill Chamberli
11 hours ago
Steve Scheuerman (Manx) left a comment for Thomas Pompeii
17 hours ago
Steve Scheuerman (Manx) left a comment for Mike LaRose
17 hours ago
Steve Scheuerman (Manx) left a comment for Jim Norwood
17 hours ago
Steve Scheuerman (Manx) left a comment for Bill Chamberli
17 hours ago
Profile IconBill Chamberli, Jim Norwood and Mike LaRose joined iKnife Collector
17 hours ago
Jim Norwood updated their profile
18 hours ago
J.J. Smith III left a comment for Jim Norwood
yesterday
Billy Oneale left a comment for Mike LaRose
yesterday
Billy Oneale left a comment for Jim Norwood
yesterday
John Burton replied to John Burton's discussion Show Us a Buck Knife photo in the group BUCK KNIVES GROUP
yesterday
John Burton replied to John Burton's discussion Show Us a Buck Knife photo in the group BUCK KNIVES GROUP
yesterday
John Burton replied to John Burton's discussion Show Us a Buck Knife photo in the group BUCK KNIVES GROUP
yesterday

Reed Cutlery Company

Visit Lee' s Cutlery

gear2survive !

KNIFE AUCTIONS

Boy's Knife is HERE

KNIFE NEWS!!!

Click to view more

JSR Sports!

NEW

© 2018   Created by Jan Carter.   Powered by

Badges  |  Report an Issue  |  Terms of Service