Welcome Home

A wise individual once told me that you could take a blade from a Rough Rider knife and interchange it with a like patterned CASE knife.  I have seen this aspect in whitttler patterns from both brands.

Recently, I've picked up several CASE 75 pattern large Stockmans and wanted to compare a Rough Rider  (RR603) to one of the CASEs.

Of my 75's I chose the Orange Comp to contrast the Yellow Comp of the Rough Rider.

Out of the box the CASE was cosmetically very good, however I had issues with the Rough Rider.  The fit and finish didn't compare.  Perhaps it was a bad run, or perhaps I just got one that was "off", but the shield was noticably off and the bolster pins wasn't polished.  I did like the ring  bolsters that Rough Rider puts on their Yellow Comp series.

Definitely not the quality that I've come to expect from Rough Rider.

The blades on both knives were pretty sharp, out of the box, with the CASE having a more polished edge.  As you can see, they are pretty much the same.

The similarly ended here though.  When looking down at the knives it's very obvious that the blades on the Rough Rider we're noticably thinner than on the CASE.   

I don't have a fancy micrometer, but I'd say that they were fully only 2/3 the thickness of the CASE, while keeping the same approximate thickness at the tang.

I don't necessarily see this as a problem, as I've seen this in other knives, but I think that Rough Rider could have thinned out the tangs also and given us a thinner overall knife.

No fancy scales either, so by my hand scales, I can't really detect a noticable difference in the weight of either one.

Bottom line, for me is, I got my CASE for roughly $50.00; I got my Rough Rider for about $12.00.  I think that I'll be carrying the Rough Rider for a bit.

After some personalization, ie lowering the sheeps foot blade and rounding out the edges of the scales I'll see how it does in the long run.

Views: 124

Replies to This Discussion

Found this YouTube comparison for the RR and CASE.

https://youtu.be/TQFaBbZ7dXA

Definitely not the quality that I've come to expect from Rough Rider.

I can honestly say I am surprised JJ.  The photos alone tell me that this is not the RR quality we have all seen in the past.  Think I will make a stop at the RR booth at Blade and see is it is happening across the board with them

I'm liking the RR now that I've got the scales smoothed down some.  I'm betting that the shield issue comes from a new batch of shields being put into scales prepped for the old shield.

I'm definitely, more than a little bit, discouraged with the blades...they've been thinned down so much it's rediculous.  Can't say that it's an isolated knife, either, because you know I got 2.

I've reviewed every YouTube video with the 603s and from what I've seen, that's the way they are.

I've never seen a Rough Rider that failed, miserably, but from my standpoint, this pattern did.

Made my mind up that I'm not going to EDC the Rough Rider.  Went looking for a Yellow Comp CASE, because I wanted a CV.  Nowhere in town had the yellow, so I picked up an Amber CV.

Let the transformation begin...

O9

Jan Carter said:

Definitely not the quality that I've come to expect from Rough Rider.

I can honestly say I am surprised JJ.  The photos alone tell me that this is not the RR quality we have all seen in the past.  Think I will make a stop at the RR booth at Blade and see is it is happening across the board with them

I posted a comment, on the RR Facebook page, about this knife.  They didn't comment on it, however they did "Like" it.

It would have been nice if they'd take the time to address the issues.

Can't wait to see it in its new form :)

Awesome!  Thanks, JJ!

In case you haven't seen the post about my CASE, it broke.  Backspring is caput.  I've sent it to CASE, for repair.

In the meantime, Tobias had checked the specs and verified the "thinness" of the blades.

CASE Specs...

Rough Rider Specs...

As can be seen, the current production Rough Riders have roughly 2/3 thickness as the CASE.

He did refer me to another Rough Rider, in red bone, that according to the specs has slightly thicker blades than the CASE.

Of course they're out of stock at SMKW but I was able to find one on eBay, so I'll have something to use while the folks up in Bradford repair my CASE.

I'll see how the red bone measures up, when it arrives.

Looks like someone at SMKW (whoever runs the RR Facebook page) got a little testy about me questioning the thickness of the blades in their new knives...

I'm taking this to mean that all the new knives will have these thin blades?

RSS

White River Knives

Latest Activity

Ricky Ray posted a status
"Clemson Tigers winning big against NC State :)"
17 minutes ago
Dennis Hibar posted photos
1 hour ago
Dennis Hibar replied to Craig Henry's discussion Case Seahorse in the group Case Fans
1 hour ago
Steve Scheuerman (Manx) left a comment for Toby
2 hours ago
Steve Scheuerman (Manx) left a comment for Kevin Holliday
2 hours ago

KnifeMaker
Toby left a comment for Jan Carter
2 hours ago
Jan Carter left a comment for Kevin Holliday
3 hours ago
Jan Carter left a comment for Kevin Holliday
3 hours ago
Jan Carter left a comment for Toby
3 hours ago
Profile IconToby and Kevin Holliday joined iKnife Collector
3 hours ago
Kevin Holliday left a comment for John Bamford
3 hours ago
John Bamford left a comment for Kevin Holliday
3 hours ago
J.J. Smith III posted a status
"eBay strikes again..."
6 hours ago
J.J. Smith III left a comment for Kevin Holliday
7 hours ago
Ricky Ray posted a status
"Watching the Brewers win game six!"
20 hours ago
Ted Hassler joined Scott King's group
yesterday

Reed Cutlery Company

Visit Lee' s Cutlery

gear2survive !

KNIFE AUCTIONS

Boy's Knife is HERE

KNIFE MAGAZINE!!!

Click to view more

JSR Sports!

NEW

© 2018   Created by Jan Carter.   Powered by

Badges  |  Report an Issue  |  Terms of Service