iKnife Collector
The online community of knife collectors, A Knife Family Forged in Steel
Need Help Identifying a Couple of Knives
I recently bought a couple of knives from a local auction and I am having some trouble identifying the maker of these two. I thought that someone could lend me some help and help identify the tang stamp on these two knives. Any and all help would be appreciated. Thanks again. Hopefully the pictures I attached worked. Thanks
- Attachments:
-
-
Knife 1.jpeg, 1.2 MB -
Knife 2.jpeg, 1.6 MB
-
Knife 3.jpeg, 1.9 MB
-
Replies to This Discussion
-
Permalink Reply by Jan Carter on
-
I have been unable to find anything yet but will continue searching. Lets hope another member has seen this before.
To be honest it does appear to be a custom marking not so much a manufactures tang
-
Permalink Reply by Steve Hanner on
-
I agree Jan looks custom for sure on that JW
-
-
That other knife I see a marking but can't make out anything.
-
-
Both of the knives have the same JW marking. I agree it is custom, but I am just having problems figuring out who the maker is.
-
-
OK well let me ask this any idea where the knives are from? Where did you buy them. That could make a difference as I can think of at least 3 custom knifemakers with those initials.
-
-
I bought them at an auction in Indianapolis, Indiana.
-
-
Thanks Craig, its a long shot but might help skinny down the list
Craig Mobley said:I bought them at an auction in Indianapolis, Indiana.
-
Permalink Reply by Thorvan Patten JR. on
-
Very nice!
-
Permalink Reply by Bill Fletcher on
-
Hello, I purchased the Cotton sampler pictured below with the Tang Stamp, JW, from eBay. The handle material is spalted maple and was made by custom knife maker Jim Watson. This tang JW looks pretty much like yours. Hopes this helps a bit, Best regards
-
-
Bill thank you for your information. You are right the JW does look very very similar. I will make sure I check it out.
Bill Fletcher said:Hello, I purchased the Cotton sampler pictured below with the Tang Stamp, JW, from eBay. The handle material is spalted maple and was made by custom knife maker Jim Watson. This tang JW looks pretty much like yours. Hopes this helps a bit, Best regards
-
-
Bill have you every had any luck finding any information online about custom knifemaker Jim Watson?
Bill Fletcher said:Hello, I purchased the Cotton sampler pictured below with the Tang Stamp, JW, from eBay. The handle material is spalted maple and was made by custom knife maker Jim Watson. This tang JW looks pretty much like yours. Hopes this helps a bit, Best regards
-
-
Well if its this Jim Watson he is quite famous and has written a book:
Watson
In a process handed down from his grandfather, Jim Watson explains and illustrates sharpening techniques for numerous woodcarving tools and knives of various sizes and shapes including pocket knives and kitchen knives. The necessary materials for proper sharpening are listed and discussed with methods for reconditioning and making you own new knives and tools as well as information on resurfacing the sharpening stones. By following Jim's instructions and adding a little practice and patience, everyone will be able to achieve and maintain a superior edge, as keen as the piece of steel will allow.
175 pages, 6 x 9 (Paperback)
Item #: BK650
whiteriverknives.com
Latest Activity
KnifeMakerblack mamba knives replied to black mamba knives's discussion Anyone else noticing printed "Damascus" creeping into the collectible side of the hobby?
KnifeMakerblack mamba knives replied to black mamba knives's discussion Anyone else noticing printed "Damascus" creeping into the collectible side of the hobby?
2021 CalendarJ.J. Smith III replied to black mamba knives's discussion Anyone else noticing printed "Damascus" creeping into the collectible side of the hobby?
2021 CalendarJ.J. Smith III replied to black mamba knives's discussion Handles that keep changing after you buy them
© 2026 Created by Jan Carter.
Powered by
