A friend of the Harvey Family did it for the show

Donnie saw the mermaid series at Harveys but I did not yet.  I will check it out on Friday :).  That one looks nice

That may be a raffle

Very nice quilt, Jan!

Hello all,

I just purchased a nice looking trapper knife (with prime stag handles) that is supposed to be in "new" condition, but there are blade rubs on the clip blade, right were the etching pattern is, and am debating a return. I know rubs are fairly common, but how much do they detract from the actual value of the knife? If I decide to sell this sometime down the road, would it be a major contention?

Thanks,
P.

Paul the repair dept. and arrange to send it back for repair. They will fix it.

YES! You will have to sell this knife as used and in good condition. You should expect to get about $45. I would return it or use it for an EDC. Sorry for the bad news. I love the Trapper design too.

Paul you will have to sell it as repaired by factory...but if you pay for the repair you will be way in too deep. Just my opinion after 25 years of getting burned on occasion.

Thanks guys. Fortunately, there is a return policy. I'm going to try to exchange it for another one.

Wonderful quilt...made in america too!!!!!!!!!!!!!!!...........

That quilt will be a raffle...These knives will be the auctions

Made in the US.  Created by Ms Annie.  Raffled off tomorrow.  They have two artisans tour auctions. 

good news I had it wrong.  The charity auction for the quilt will be in dec

Had a great day met some wonderful folks (talked a god deal about iknifecollector and you all)

Wish I could have been there!

A special thank you to Clay, Mrs. Harvey, Will, Ricky, Paul and Mike

A wonderful Day!

The Case quilt is a charity auction and will be drawn on Dec 15th.  You can call and purchase tickets by phone (813) 996-2400

3 for $5.00

8 for $10.00

There are also a very few Harvey's knives left

 phone (813) 996-2400

Here is a photo of the latest Case acquired. It is a single bladed CV Trapper with a liner lock and pocket clip. The handles are Chestnut Bone and the pattern is #54L and the item number is 30112. I have been carrying this knife with yellow handles for about six months and just find it to be my favorite EDC even over all of the tactical autos I own.

I will admit I have many mistresses and one is any folding pocket knife with a swing guard. Add a swing guard, liner lock (my favorite locking system) and pocket clip and I am in love again. Sadly this animal does not exist.

I have strongly suggested to Case, Tuna Valley, GEC and Moore Maker to make an XL swing guard with the liner lock and pocket clip. I am thinking the sized of the Case large single bladed hunter size with less expensive handles to keep the price down so as to be affordable by law enforcement, firemen, military and other underpaid public servants. Take this classic timeless design and jazz it up to a combat folding pocket knife. What do you think people? Would this design and size of knife sell? Would you want to have one? If you say no then you need to check your pulse. Please give some feed back.

That's a sweet-looking knife, Clint! I might look into getting one of those. I'm especially fond of the trapper design!

Paul if you purchase this knife you will not regret having done so. I was truly surprised how much I loved this knife.

I like the single blade "Trapper". The smooth Chestnut Bone looks great! Case does bone good!

I like this new Linda Karst scrimshaw!

It really does look great but  I'd like it better on a Case Whaler or marlin spike knife. (I'm turning into a curmudgeon)

You right Toby, they should do some on those! Maybe they will?

It would be nice but I sort of doubt it.  The Case Marlin Spike was outsourced to the old Camillus Factory.   The Case Whalers were made on the #99 frame and haven't been made since 1964!  Talk about being in the Vault!

You could always try pleading and crying like I do.

Craig, Apparently you haven't seen my posts on the Rough Rider, and SMKW facebook pages.  LOL

We need to start a "Make Our Knife Enforcement Group". I'll call Two Fingers Eddie in Chicago.

I didn't win the Shepherd Hills Cutlery blue Peanut.

I kinda like the shield on these......

Yes it is nice. I hope Case mixes up some of their shield designs.

I'd like to see some more old timey designs.

Ordered my first Case knives in 13 years!

Is it a peanut?

Could be......

Is it a canoe?

I don't know, but I finally bought the Sunset Winterbottom bone Moose on Friday. That's the first Case knife I have bought since being able to buy the two Cheetahs in the drawing last winter.I have had my eye on this for awhile. I also like the new sawcut bone that Case is doing.

Sawcut bone? Like this? I like it too.

That was an interesting video, Jan. I'm seriously thinking of making something similar out of old milk jugs, pvc pipe and duct tape!

Just like that, Craig

I also like their sawcut Amber Bone on their Rancher series, which is similar.

40% off, their discount price, a Case knife to be announced midnight (EST) Dec. 1 at Shepherd Hills Cutlery. - "Offer good while supplies last" - I bet they won't last long......whatever it is.

Craig if the original knife they offer sells out they will offer another pattern or a variations of that pattern.

Oh okay, thanks Gerald, I didn't know that. 

Got my new Case knives! Hopefully I can get some pictures and a review in the next few days.

My new Case knives are first class!!!

All of my Case knives are stainless steel.  I am wondering what  I will need to do if a purchase a case CV knife

Jack if it's going to be a user just a light coat of oil on the blades. If it's a collector Ren wax will help protect it.

Here's one I put a patina on using vinegar.