Welcome Home...THANK YOU FOR BEING A PART OF OUR COMMUNITY

New handle for a Spyderco Dragonfly 2 with a single piece handle. HELP!

I have been making scales for my knives for about a year.  They all have liners and ways to just "copy" everything.  Especially hole placement.  That is one thing that HAS to be perfect.  I'm putting pictures of my progress so far and hope someone (anyone, more than one, etc.) can give me some advice.  I would love to learn from other's mistakes instead of my own. :)  I hope you see and figure out my thinking with pictures instead of my explaining.  If you have questions or tips please ask or give.  Thanks.  Starting with the backspacer. I'm planning on gluing the handle sides and backspacer together.  Then shaping it.

Below is part of my next step and the one that worry's me.  Placing the lockbar and blade pivot holes correctly. Since the original handle can't be disassembled I'm making a template for the holes.  Placing the template on my new handle material is the issue.  Any tips are appreciated.

Views: 1371

Reply to This

Replies to This Discussion

Jack,

I checked with a knifemaker here and this was the thought

 clamp that old handle to the new handle material and drill right through those holes  That should locate the pivot and lock bar holes then work from there

Hope that helps some

I can't do that with this knife.  The handle is one piece FRN (Fiberglass Reinforced Nylon) so I'd need to drill through the holes in both scales.  This would be ok except the hole on one side has a flat spot inside the hole.  This lines up with a flat spot on the pin so it won't turn inside the knife.  If I drill through the holes I'd round off the inside of this hole pretty much ruining the original handle.  I don't want to do that.  Thanks for the suggestion though.  I'm really new at this and can use all the help I can get.

Jan Carter said:

Jack,

I checked with a knifemaker here and this was the thought

 clamp that old handle to the new handle material and drill right through those holes  That should locate the pivot and lock bar holes then work from there

Hope that helps some

Made a little progress.  The knife is pretty much working fine now.  I have the handle together and the epoxy is drying.  Here's pictures.

I hope I did the replying correctly. :)

Jack Haskins, Jr. said:

I can't do that with this knife.  The handle is one piece FRN (Fiberglass Reinforced Nylon) so I'd need to drill through the holes in both scales.  This would be ok except the hole on one side has a flat spot inside the hole.  This lines up with a flat spot on the pin so it won't turn inside the knife.  If I drill through the holes I'd round off the inside of this hole pretty much ruining the original handle.  I don't want to do that.  Thanks for the suggestion though.  I'm really new at this and can use all the help I can get.

Jan Carter said:

Jack,

I checked with a knifemaker here and this was the thought

 clamp that old handle to the new handle material and drill right through those holes  That should locate the pivot and lock bar holes then work from there

Hope that helps some

Finished.

I know. I screwed the clip up.

I would use the original handle as a temp plate. Draw the shape but also use something to mark the holes on the new material, through the holes on the original scales. I hope you understand what I mean.

I do know what you mean.  If you are referring to the clip position  that's not possible.  There are two grooves in the scale that the wires fit into.  They don't go all the way through the material so I can't use the original scale as a template like you can for shape and hole position.  I just had to eyeball it.  But in this case though I got in a hurry because it was the last thing I did and was looking forward to having it completed.  My lines for the grooves were not lined up correctly.  It would have been easy to tell if only I had doublechecked one more time before I cut the grooves.  But nooo, not me. :( lol

Robert Burris said:

I would use the original handle as a temp plate. Draw the shape but also use something to mark the holes on the new material, through the holes on the original scales. I hope you understand what I mean.

What I do some times is put the project down, until the next day. I find, I am fresh and ideas and answers come to me more freely. Although, I have been guilty of rushing to the finish but I almost always wish that I hadn't. Human, nature, I guess..

Hi Jack,

Jan is right. That's what I do. I use the original hande as a template. If the knife has a liner I use the liner.

It works every time and it looks like it worked for you too.

The finished knife is going awesome.

John

Reply to Discussion

RSS

White River Knives

Latest Activity

Visit Lee' s Cutlery

KNIFE AUCTIONS

KNIFE MAGAZINE!!!

tsaknives.com

JSR Sports!

Click to visit

© 2024   Created by Jan Carter.   Powered by

Badges  |  Report an Issue  |  Terms of Service