Tools for knife enthusiasts
A place to discuss tools specifically relevant to knife making and restoration. But since Boys (and girls) like toys, we'll likely end up talking about tools in general anyway!See More
iKnife Collector
The online community of knife collectors, A Knife Family Forged in Steel
-
allanm
- Male
- Yorktown, VA
- United States
- User/Collector
- Blog Posts
- Discussions (164)
- Events
- Groups (11)
- Photos (24)
- Photo Albums (2)
- Videos
allanm's Groups
allanm's Discussions
Smith & Wesson SWAT First Millennium Run - value estimates?
Started this discussion. Last reply by dead_left_knife_guy Apr 8, 2017. 6 Replies 1 Like
I've been searching and don't see any better group to place this question under. Maybe I'm just not looking hard enough or need to start a general knife values / questions area somewhere.Somebody at…Continue
Jantz Wyoming kit knife
Started this discussion. Last reply by Jan Carter Mar 12, 2017. 12 Replies 3 Likes
I just finished my first new (from Jantz Wyoming kit!) creation. My first knife work attempt was restoration (or rather re-scaling) and old damaged and abused Western. I decided to start with a pair…Continue
Band saw vs table saw
Started this discussion. Last reply by D ale Dec 20, 2016. 19 Replies 2 Likes
This is a general question as I expand my experience and tools, which I know may be very subjective and depend on many factors.I have very little space, and few tools, so looking at smaller tools -…Continue
Knife restoration - Western brand, made in Boulder, CO
Started this discussion. Last reply by allanm Aug 1, 2016. 8 Replies 2 Likes
I joined up some time ago, and mentioned that I had an old Western brand knife that my wife had brought back from an auction - badly abused and just getting dumped basically, so she paid 25c thinking…Continue
Tags: repair, restoration, knife
allanm's Page
Latest Activity
Tools for knife enthusiasts
A place to discuss tools specifically relevant to knife making and restoration. But since Boys (and girls) like toys, we'll likely end up talking about tools in general anyway!See More
Tools for knife enthusiasts
A place to discuss tools specifically relevant to knife making and restoration. But since Boys (and girls) like toys, we'll likely end up talking about tools in general anyway!See More
"1) I like the clean look overall with plenty of images
2) I don't like the big ugly purple block at the top right on the home page, that's like a spotlight shining in my eyes, totally drawing attention from the image to the left and looks…"
Profile Information
- Profile
- User/Collector
- How did you hear about iKnifeCollector?
- web search
- Do you currently subscribe to any knife publication (offline)
- No
- How long have you collected knives?
- 3- 5 years
- Favorite Kind of Knives
- old, with interesting history
- About Me
- Immigrant from Africa, hunter, shooter, knife collector
allanm's Photos
Comment Wall (27 comments)
- At 13:45 on January 27, 2019,
Steve Scheuerman (Manx) said…
- At 15:00 on January 26, 2019,
Jan Carter said…
Happy Birthday Allan
- At 17:54 on January 26, 2018,
- At 7:49 on January 26, 2018,
- At 22:30 on July 1, 2017,
J.J. Smith III said…
Thanks for being an active member here at iKC. Without participation we'd be a pretty slow site.
- At 16:06 on July 1, 2017,
- At 17:44 on April 8, 2017,
In MemoriamD ale said… I understand, allanm.
..and..
Can very truthfully state that 99+% of my PM's (individual communications here on iKC) are with 3 individuals .. JJ, Jan, & John Bamford. I too take my privacy VERY seriously.
.
Re: Your possible project using 5.56 casing ends. I believe the most economical approach would be for you to fabricate the wooden clamping fixtures out of existing wood scrap that you've left over from previous projects that would ultimately end up working with your existing metal drill press vise.
.
regards
D ale
- At 15:55 on April 7, 2017,
In MemoriamD ale said… It would be far easier & more economical to simply make inserts that would fit in your existing drill press vise !!!
.
However .. should you decide upon purchasing any of the listed items .. I highly suggest that you install metal "through rods" at the corners. This will greatly enhance the structural integrity of the vise. I am not a carpenter ..so.. I do not know the proper terminology used in designating the size of nails. Regardless .. choose a nail that is equal to or slightly exceeds the height of the vise & trim it such that its length is equal to the height of the vise. Then drill a hole @ each corner (equidistant from the edges, i.e. center the hole in the corners) that is ever so slightly larger than the chosen nail size. Such that the nail just drops in the hole. OR, simply chose whatever nail size you have on hand and can trim to the required length (equal to the height of the vise).
.
Then .. fill the hole with a good quality wood glue .. Elmers or Gorrilla or any good quality liquid adhesive that you have on hand. Then .. slide the the pre-trimmed metal pin into said hole & let cure overnight.
.
The addition of a metal through pin @ the corners will greatly enhance the structural integrity of the vise. Mine came with them already installed. Not all do.
- At 15:10 on April 7, 2017,
In MemoriamD ale said… $11.88 model .. very close to the size I have .. 125mm long X 80mm wide X 60mm high.
- At 15:06 on April 7, 2017,
In MemoriamD ale said… $ 4.52 model … 120mm X 90mm X 56mm / 4.72” X 3.54” X 2.21” (L * W * H)
whiteriverknives.com
Latest Activity
"Not sure where is best to put this...
My calendar arrived today! (12/15). Going to hang it in my office at work. :)"
"Just saw the latest CASE drop with our damascus. AMAZING Been waiting for them to do a Barlow!! and a folding Hunter!! EPIC! HHH And CASE"
© 2025 Created by Jan Carter.
Powered by
