Welcome Home...THANK YOU FOR BEING A PART OF OUR COMMUNITY

Check out this beautiful piece of work lol!!
I am wondering if any guys or girls here have any suggestions on possible restoring this thing. Otherwise it will be going in the trash.

This is a result of leaving it at my parents house and my father adopting it.

Views: 348

Attachments:

Replies to This Discussion

Yup, its had a hard life but, does it open and close ok?  If the action is good on the knife, its worth fixing back up into a knife!  That's one I would save personally for a nice few evenings at the workbench. The stag appears to be just fine, just the blade needs to be re-profiled and the rust/stains removed.  Definitely worth saving and not trashing by first impressions!

Yea the action was a bit rough until I put a little oil and worked the rust out. Now it seems to open and close fine. I could try do put a point back on the blade, but knowing myself it would really bug me soo I'm thinking of giving GEC a call to see if they would put a new blade on it.

Mackensie,

Let me know if that is something they would do.  I do not know that I have ever had one sent in to GEC for that.  If the action is back re-profiling that blade is a great option also 

well,  there are a few other issues.  Has developed  a little blade wiggle and a few gaps so I thought I would call tomorrow.  It couldn't hurt to ask.

Possibilities abound...trashing it is not one though.

I'm w/ JJ .. lots of options .. trashing is not one I'd personally consider.

Re-profiling the blade is an obvious necessity.

You may have to "drop the point" to get the tip to lie within the frame.

I'd only do that enough to get it to rest below the top edge of the frame.

From there .. I'd curve the edge up to meet the new end of the spine.

Proceed SLOWLY & keep a bucket of water handy.

You do not want to change the temper of the blade by building up heat.

.

As far as the side play you mentioned .. insert a 0.001" feeler gauge between the frame & the pivot point.

Then .. use a small ball peen to GENTLY remove said play.

.

IF .. GEC will replace the blade .. GREAT.

However .. that may not be the most economical approach.

.

Reconditioning the knife yourself will simply cost you some time.

Cool sounds good. Thank you for the advise. This will just have to be a new project for me when I get some spare time.
Yep, I could see a nice wharnie mod ,for this one, but that's me.
Dropping the point, and reworking the swedge, as Dale suggests, will give you a nice user when you finish.

I can rebuild the point on that knife if you're interested.  Below are Before/After photos of an Old Timer I had laying around with a point missing off one of the secondary blades.  Rebuilt point looks 90% or better, although it is probably not something you'd want to use excessively.  In my opinion it certainly looks better than a missing point and is fine for display purposes.  I had one blade I rebuilt professionally sharpened and the new point held up to that process and actually retained a very sharp edge when they were done. 

Attachments:

Andy, that re grind came out real well!

Thanks, Jan, but it technically isn't a re-grind....I actually added new material to the point, if that makes any sense, using carbon steel sawblades.  I took some photos of the procedure, will try to include them here below.....You will notice I rebuilt the point and then ground down the extraneous material to blend it in with the rest of the blade.  Metal coloring is very similar and the repair is barely noticeable.  In fact, the guy who sharpened that blade never noticed it had been rebuilt.  I rebuilt the point on a WW2 Camillus folder in similar fashion and carry it often.  Actually carried the Camillus today and cut a 1.5" thick ribeye steak with it.  Yum.

I will add that this procedure does NOT involve using excessive heat, so it shouldn't affect the temper of the blade significantly.  I use a laser welder that focuses the work to a tiny pinpoint and hold the blade in my hands as I work on it, so it doesn't even get hot enough to burn my fingers.  This procedure has worked great on some rusty old broken-tipped basket cases.  I would love to get my hands on Mackenzie's knife above....Could put a new tip on it and make it really nice, probably not showroom perfect, but much better than grinding down the blade to match the broken tip.

Jan Carter said:

Andy, that re grind came out real well!

Attachments:
Andy I would like to take you up on the offer to rebuild the blade. At this point it seems like my best option. How much are you asking for the Job?

RSS

White River Knives

Latest Activity

Visit Lee' s Cutlery

KNIFE AUCTIONS

KNIFE MAGAZINE!!!

tsaknives.com

JSR Sports!

Click to visit

© 2024   Created by Jan Carter.   Powered by

Badges  |  Report an Issue  |  Terms of Service