iKnife Collector
The online community of knife collectors, A Knife Family Forged in Steel
iKC Member in Need Request #3 - Sears Craftsman 3 Blade Folder
The Need
Similar to my first request, please take a look at this and the other postings I have similar to this one and share with me what you know about it. My goal is to use the information you provide to properly market and sell these knives to get a reasonable sale price while letting the buyer enjoy the full value of the piece.
Craftsman Folder – What I Think I Know to be True
This is what I believe to be true so far about this knife:
- Not a thing
What I want to Know
Based on the bullet info above and judging the best you can from the photos, I would like to know the following:
- What kind of folder is this? (frame type)
- Manufacturer?
- Estimate year of knife manufacture?
- Are the scales Delrin?
- Are the blades Carbon steel or badly pitted SS?
- Should I clean & polish it or leave it as is?
- What, in your opinion, is the value of the knife?
- What, in your opinion, is a good sale price?
Please feel free to ask me questions, request additional photos, or whatever in order to assist you in your evaluations. Please also feel free to correct my understandings with additional facts, as I want the best info I can get to support the sale.
Thank you for your comments and assistance – it is greatly appreciated!
Replies to This Discussion
-
Permalink Reply by Tobias Gibson on
-
These were made for Sears by Camillus. The knife is a Stockman. I'd clean and oil it but don't do any polishing. Camillus used a thermal plastic that was similar to Delrin but it was not provided by DuPont. The more appropriate term would by composition.
I'm sorry, I don't which Stockman frame Camillus used for this Stockman. How long is the closed knife.
The main selling points are the knife was made by Camillus and has a Craftsman Shield. The negative is condition.
I'd say $20-$45! I know that's a big spread but it really depends on how bad a Camillus Stockman fan wants it.
I'll check my records and see if I have info on when Camillus made Craftsman knives. I'm guessing the blades are Stainless, most likely 440. Compare them to the Springs. The springs could very well be Carbon. If they are, it makes it an older Camillus knife.
-
Permalink Reply by Lars Ray on
-
Thank you Tobias! The Stockman is 4" closed. To me, the blade material and the springs look the same. Is there a significant difference between the two that makes it easy to determine?
Tobias Gibson said:These were made for Sears by Camillus. The knife is a Stockman. I'd clean and oil it but don't do any polishing. Camillus used a thermal plastic that was similar to Delrin but it was not provided by DuPont. The more appropriate term would by composition.
I'm sorry, I don't which Stockman frame Camillus used for this Stockman. How long is the closed knife.
The main selling points are the knife was made by Camillus and has a Craftsman Shield. The negative is condition.
I'd say $20-$45! I know that's a big spread but it really depends on how bad a Camillus Stockman fan wants it.
I'll check my records and see if I have info on when Camillus made Craftsman knives. I'm guessing the blades are Stainless, most likely 440. Compare them to the Springs. The springs could very well be Carbon. If they are, it makes it an older Camillus knife.
-
-
Normally the older carbon steel springs will develop a nice patina and turn almost black against the brass liners. The blades will remain silvery, like yours. If the blades and springs are both the same my bet is both are stainless.
-
-
Based on your assessment of my description, I would concur. Thank you for your time and inputs on all these!
Tobias Gibson said:Normally the older carbon steel springs will develop a nice patina and turn almost black against the brass liners. The blades will remain silvery, like yours. If the blades and springs are both the same my bet is both are stainless.
-
-
I found some additional info on this stockman - not sure if applies to all models 95044 and 95045's
- After cleaning some surface junk off the blade, I can read the tang stamp - "Craftsman" over "USA" over 95044
- Models 95044 (pre 1977) and 95045 were SFO knives from Schrade, and referred to by Sears as Bowie Stockmans.
- Blades and springs are actually 1095 carbon steel, which explains why mine look like they do.
- Since these are Schrade, then the handles are saw cut delrin
- This info doesn't change a thing for value or demand...just answers some questions.
-
Permalink Reply by Michael Squier on
-
Get yourself a can of Neverdull Magic Wadding and use it to clean the metal surfaces, it cleans and very lightly polishes but doesnt scratch or remove any metal. it works well on carbon steel to lighten the staining but does not remove it all. You can get it at hardware stores. it will clean up stainless realy well too. if the metalis real rusty you need something else. neat littleknife it will clean up and be saleable.
-
-
Interesting - never heard on that compound...gonna have to look that up! Thank you -
Michael Squier said:Get yourself a can of Neverdull Magic Wadding and use it to clean the metal surfaces, it cleans and very lightly polishes but doesnt scratch or remove any metal. it works well on carbon steel to lighten the staining but does not remove it all. You can get it at hardware stores. it will clean up stainless realy well too. if the metalis real rusty you need something else. neat littleknife it will clean up and be saleable.
White River Knives
Latest Activity
KnifeMakerAndy Larrison added a discussion to the group Knife Repair, Modification, Restoration & Improvement
KNIFE AUCTIONS
KNIFE MAGAZINE!!!
tsaknives.com
JSR Sports!
Click to visit
© 2024 Created by Jan Carter.
Powered by
